Ti3C2纳米层状材料对废水中Cr（Ⅵ）的光催化去除性能

以Ti₃AlC₂为原料,采用HF刻蚀工艺制备出12种Ti₃C₂纳米层状材料,对其形貌进行了表征,并考察了以其作为光催化剂对废水中Cr（Ⅵ）的处理效果。实验结果表明：HF体积分数为80%、刻蚀时间为48 h时得到的MX-80-48的形貌较好;MX-80-48具有类似石墨烯的二维层状结构,纳米层厚度约20~50 nm,孔径2~10 nm,比表面积14.8 m²/g,在400~700 nm可见光范围内表现出强烈的吸光性;当Cr（Ⅵ）的初始质量浓度为40.00 mg/L、MX-80-48投加量为200 mg/L、pH=2、反应时间4 h（暗反应1 h+光照3 h）时,Cr（Ⅵ）去除率可达100%。     

SMBBR-AF-SMBBR组合工艺处理高氨氮农药废水

采用特异性移动床生物膜反应器(SMBBR)和厌氧生物滤池(AF)组合工艺处理高氨氮农药废水。考察了HRT、pH和DO等工艺条件对SMBBR-AF-SMBBR组合工艺运行稳定期COD和氨氮去除率的影响。试验结果表明,在进水COD为2 408~7 440 mg/L、ρ(NH_4~+-N)为160.21~433.84 mg/L、TN为208.27~537.65 mg/L、HRT为8d、pH为8.0、DO为4 mg/L的条件下,处理后出水平均COD为342 mg/L,COD去除率达92.3%;ρ(NH_4~+-N)小于4.0mg/L,氨氮平均去除率为89.2%;TN小于50 mg/L,平均TN去除达83.0%。出水各指标均优于原A2O工艺出水。     

煤制乙二醇废水预处理装置的工业化调试

针对煤制乙二醇废水含高浓度硝酸盐氮的特点,设计了缺氧膨胀床(AEB)反应器预处理装置,并进行了工业化启动和调试运行,考察了其在反硝化连续流运行条件下的处理效果及工艺参数变化。结果表明,AEB反应器启动后,填料层生物膜挂膜快速且生长稳定。反应器在工业化调试阶段运行稳定,COD和TN的去除率和去除负荷较为稳定。在受到来水冲击后,AEB反应器处理效果稳定,出水可在短期内恢复正常。该技术的系统操控参数范围较广,易于工业化操控运行,在煤制乙二醇废水和其他含高浓度硝酸盐氮废水的处理中具有较大的推广价值。     

纳米铁催化分解高氯酸盐废水的反应动力学

通过实验考察了酸性条件下纳米铁催化分解高氯酸盐过程中的影响因素,对其分解的动力学进行了研究,并对纳米铁催化剂结构及微观形貌进行SEM、EDS和XRD表征分析。利用阿仑尼乌斯方程和幂指数方程拟合反应动力学方程,获得了高氯酸盐分解动力学方程Ct=C0exp{-0.03773exp(-201.65/T)[H]0.191t},理论的计算值与实验值吻合较好,误差在15%以内。     

Challenges for modelling and integrating environmental performances in concept design: the case of an automotive component lightweighting

The objective of this paper is to discuss the main barriers for modelling and integrating the environmental performances in the automotive concept design. Incorporating environmental assessment in the early design phase of a vehicle component is known as an important challenge that car makers need to face in order to develop more sustainable design solutions; in this regard, the Life Cycle Assessment is the most widespread methodology for the environmental assessment and comparison of alternatives. The present work illustrates the combination of such methodology with the traditional design procedure at two different levels of the component design phase, material choice and concept design. In particular, the potential benefits originated by a lightweight solution for the automotive component Throttle Body are evaluated by considering environmental and technical implications at the same level. The case study shows that a multi-disciplinary approach for design effectively allows the integration of the environmental issue in the company’s established procedures. However, interpretation of results is still a challenging aspect due to the inevitable contradicting elements which should not discourage to develop comprehensive sustainability assessment within the early design stage.     

亲水性多孔载体在流化床中的生物膜形成过程分析

采用实验制备的一种新型亲水性多孔聚合物作为流化床反应器中生物膜附着生长的载体,实现流态化水力条件下的生物挂膜过程.在3个结构尺寸相同的流化床反应器中考察了接种污泥浓度、进水有机负荷及载体粒径对亲水性多孔载体生物挂膜量的影响,试验结果表明,接种污泥浓度为30 g VSS/L、进水TOC值为350 mg/L、载体粒径为5～8 mm时载体表面的附着生物量最大,反应器运行12 d的载体附着生物量达到4.45 g VSS/L,膜结构稳定,表现出较活性污泥法更高的活性.在进水TOC、氨氮浓度分别为350 ms/L、50 mg/L,HRT为6 h的情况下,两者的去除率分别达到了97.1%和64.3%,表明载体上的生物膜对污水中TOC及氨氮的去除表现出高效率.挂膜后载体表面上的微生物以丝状菌为主,孔壁上的微生物以球菌和杆菌为主要生物相,证明载体内外表面皆适宜微生物的生长,并且形成合理的生物相分布.     

Relationships between anaerobic consortia and removal efficiencies in an UASB reactor degrading 2,4 dichlorophenol (DCP)

To gain more insight into the interactions between anaerobic bacteria and reactor performances (chemical oxygen demand-COD, 2,4 dichlorophenol-2,4 DCP removals, volatile fatty acid-VFA, and methane gas productions) and how they depended on operational conditions the microbial variations in the anaerobic granular sludge from an upflow anaerobic sludge blanket (UASB) reactor treating 2,4 DCP was studied. The study was composed of two parts. In the first part, the numbers of methanogens and acedogens in the anaerobic granular sludge were counted at different COD removal efficiencies. The relationships between the numbers of methanogens, the methane gas production and VFA production were investigated. The COD removal efficiencies increased to 74% from 30% while the number of total acedogens decreased to 10 from 30 cfu ml(-1). The number of total methanogens and acedogens varied between 11 x 10(3) and 10 x 10(9)MPN g(-1) and 10 and 30 cfu ml(-1) as the 2,4 DCP removal efficiencies were obtained between 60% and 99%, respectively. It was seen that, as the number of total acedogens decreased, the COD removal efficiencies increased. However, the number of total methanogens increased as the COD removal efficiencies increased. Correlations between the bacterial number and with the removal efficiencies obtained in different operational conditions were investigated. From the results presented in this paper a high correlation between the number of bacteria, COD removals, methane gas percentage, 2,4 DCP removals and VFA was observed. In the second part, methanogen bacteria in the anaerobic granular sludge were identified. Microbial observations and biochemical tests were applied to identify the anaerobic microorganisms from the anaerobic granular sludge. In the reactor treating 2,4 DCP, Methanobacterium bryantii, Methanobacterium formicicum, Methanobrevibacter smithii, Methanococcus voltae, Methanosarcina mazei, Methanosarcina acetivorans, Methanogenium bourgense and Methanospirillum hungatei were identified.     

山梨酸废水在ABR中的基质降解行为

稳态条件下,采用厌氧折流板反应器(anaerobic baffled reactor,ABR)处理山梨酸废水并进行基质降解动力学研究.实验表明,在污泥负荷为0.54～1.63 kg COD/(kg VSS·d)的范围内,COD去除率随着负荷的增加从85%降到55%.各隔室出水COD沿程递减,前3个隔室承担了去除COD的重要作用,但随着污泥负荷的增加,后部承担的COD去除率比例增大.基于各串联隔室完全混合的假定,推导ABR中山梨酸废水的基质降解动力学方程,并通过实验确定相关动力学参数及相应的动力学方程.实测值与预测值基本吻合.     

Effects of bed materials on the performance of an anaerobic sequencing batch biofilm reactor treating domestic sewage

The objective of this study was to determine the best performance of an anaerobic sequencing batch biofilm reactor (AnSBBR) based on the use of four different bed materials as support for biomass immobilization. The bed materials utilized were polyurethane foam (PU), vegetal carbon (VC), synthetic pumice (SP), and recycled low-density polyethylene (PE). The AnSBBR, with a total volume of 7.2L, was operated in 8-h batch cycles over 10 months, and fed with domestic sewage with an average influent chemical oxygen demand (COD) of 358+/-110mg/L. The average effluent COD values were 121+/-31, 208+/-54, 233+/-52, and 227+/-51mg/L, for PU, VC, SP, and PE, respectively. A modified first-order kinetic model was adjusted to temporal profiles of COD during a batch cycle, and the apparent kinetic constants were 0.52+/-0.05, 0.37+/-0.05, 0.80+/-0.04, and 0.30+/-0.02h(-1) for PU, VC, SP, and PE, respectively. Specific substrate utilization rates of 1.08, 0.11, and 0.86mg COD/mgVS day were obtained for PU, VC, and PE, respectively. Although SP yielded the highest kinetic coefficient, PU was considered the best support, since SP presented loss of chemical constituents during the reactor's operational phase. In addition, findings on the microbial community were associated with the reactor's performance data. Although PE did not show a satisfactory performance, an interesting microbial diversity was found on its surface. Based on the morphology and denaturing gradient gel electrophoresis (DGGE) results, PE showed the best capacity for promoting the attachment of methanogenic organisms, and is therefore a material that merits further analysis. PU was considered the most suitable material showing the best performance in terms of efficiency of solids and COD removal.     

Fe0/厌氧微生物联合体系处理2,4,6-三氯酚影响因素的研究

利用Fe⁰/厌氧微生物联合体系对2,4,6-三氯酚(2,4,6-TCP)进行降解研究。结果表明，Fe0/厌氧微生物联合体系可以有效降解2,4,6-TCP，Fe⁰与厌氧微生物之间存在明显的协同效应。Fe⁰/厌氧微生物联合体系处理2,4,6-TCP的最优条件为：微生物接种量0.434 g VSS/L，Fe⁰投加量15 g/L，体系初始pH值7.0～8.0。